Is your Samsung dryer not heating? what happens when the dryer doesn’t heat? How do you fix it?
So if you don’t know how to fix it, we are here to help you. Here are some solutions that can help you fix the Samsung dryer not getting hot issue. Let’s get into details.
Why Is The Samsung Dryer Not Heating Up?
The Samsung dryer not heating up is one of the most typical problems with Samsung dryers. Most often, a burned heating element is at blame if your Samsung dryer won’t heat up.
The dryer may overheat for a variety of reasons, including exhaust venting, a blown thermal cut-off fuse, a thermostat, or a bad control board heating relay. It might also be brought on by a motor or a bad power source.
Simply scroll down and read the suggested fixes below if you want to know what the issue with the Samsung dryer no heat is and how to solve it:
Fix 1: Clean the Dryer Vent
Make sure your dryer vent is clear before continuing. Because there are a variety of possible causes for the dryer not to heat up. How to clean it is as follows:
- Shut off the dryer’s gas or power supply.
- Take out the screws keeping the vent cover in place.
- The dryer’s vent line should then be disconnected.
- Pour a tiny amount of water and baking soda through the vent.
- If you notice bubbles, there is a blockage and the baking soda will clear it. Try again later if necessary.
Fix 2: Check the Heating Element
Your Samsung dryer has to produce heat before it can finish drying your clothing. The Samsung dryer heating element is used in this situation. Samsung dryer heating problems are frequently caused by a burned-out heating element. Let’s check it out:
- Remove the dryer’s plug from the power supply. Turn off the gas if you are using a gas dryer.
- Find the heating component. In the majority of types, the heating coils and heating element leads are enclosed in a metal frame.
- Look for damage to the element, such as broken coils.
- Check the continuity of the heating element with a multimeter. The heating element will need to be replaced if the multimeter test results are negative.
Fix 3: Check Incoming Power
A dryer consumes a lot of electricity, especially when the heating element is involved. For an electric dryer to function properly, it needs two legs of 120 volts AC (250 volts total). Sometimes one of the fuses will trip, leaving the dryer running but without heat. To examine the fuses:
- Locate the fuse box in your home.
- Find the appropriate fuses for the dryer.
- Using a multimeter, check each fuse to make sure it has the right voltage; if not, replace it.
Fix 4: Check Your Flame Sensor
The flame sensor may be the other reason why the Samsung dryer not getting hot and here is how you test it:
- The dryer’s power source should first be turned off.
- Remove the top and side panels, if necessary, and look for the flame sensor.
- Check the sensor’s continuity with a multimeter (make sure it is at room temperature when you check it).
- You can inspect the next component if the sensor exhibits continuity, indicating that it is functioning properly. It will need to be replaced, though, if the test reveals no continuity.
Fix 5: Check the Thermal Fuse
A dryer’s thermal fuse must be replaced once it blows, unlike a thermostat, which may reset itself, for the dryer to function. Now:
- Set the multimeter’s “Ohms of resistance” dial to the minimum value.
- Touch the right side of your multimeter leads to the right side of your thermal fuse, then do the same with the left multimeter lead to check if the fuse has blown.
- The fuse has no continuity, which indicates that it has blown and has to be changed if the meter display shows no discernible change.
- The fuse has electrical continuity and hasn’t blown if the meter’s display reads 0 Ohms of resistance. It will require replacement.
Fix 6:Dryer Lint Filter
Most of the little pieces of lint that get caught in your dryer vent are kept out by dryer lint filters. Let’s check how to clean them:
- Pull the lint filter up to remove it after opening the door.
- Remove the inner filter after opening the outer filter.
- Both the inner and outer filters should be unfolded.
- With your hands or a hose attachment from a vacuum cleaner, remove all the extra lint.
- After briefly soaking the loosened residue in hot water, remove it with a sponge or nylon brush.
- Before you put it back, dry it; just don’t dry it in the sun.
Fix 7: Test the Thermostat
The cycling thermostat and the high-limit thermostat are the two types of thermostats found in dryers. The thermostat is constantly in use and could eventually break down.
When that occurs, it may not recognize that the temperature inside the dryer is too low and resulting in the Samsung dryer not getting hot. As an example, check it out:
- Verify that the power is still off.
- Track down the thermostat.
- To check for continuity, use a multimeter to test the thermostat.
- If there isn’t a beep, something is malfunctioning and needs to be changed.
- If the test reveals no continuity, the component must be replaced; if it reveals continuity, it is operating properly, and you can on to the next component for inspection.
Fix 8: Replace Damaged Motor
The motor would likely be the cause if none of the aforementioned explanations held. Your dryer’s motor may fail, causing it to cease spinning. Your Samsung dryer may be unable to heat up due to a damaged motor. Let’s check it:
- Unplug your dryer and give it a gentle shake.
- If you encounter a difficult object, it can be a motor component and the motor itself is broken.
- The motor needs to be replaced at that point with a new one.
Wrapping up
You should now have a better idea of how to fix a Samsung dryer not heating. If none of the aforementioned fixes worked, it’s time to call a qualified professional to solve the issue. We sincerely hope that you find this guide to be helpful and encourage you to check back frequently for updates.
